IMPORTANT: Read carefully before assembly and use. ©2014 Techtronic Floor Care Technology Limited. All Rights Reserved. Distributed by, Royal Applian
7NOTE: For best results, use straight, parallel strokes. Overlap strokes by 1 in. to help prevent streaking.1 42 3Plug in. Step on the handle release
8For best cleaning results, end with more dry strokes. (Continue using dry strokes until little water is visible passing through the nozzle.)NOTE: Emp
9142 3Grasp Dirty Water Tank handle and push latch to release. Pull tank out at an angle like this.Replace lid by lining up the hinge and pulling latc
10Automatic Shutoff:5Insert Dirty Water Tank at an angle back into cleaner until it clicks into place.Your carpet washer is equipped with a shut-off
111 2Place handle in upright position.Slide the hose on the tool's connector until it locks. Push forward with your thumb and on the latch to rem
12Upholstery Tool: Multi-Floor Squeegee*: *Select Models OnlyThe Upholstery Tool’s built-in brush provides scrubbing action.The Multi-Floor Squeegee e
131 2 3Open Accessory Hose Suction Port at the bottom of the Dirty Water Tank. Insert hose end connector by inserting rmly into Suction Port.Press
1421Press the trigger to release air and uid. Replace Hose and tools in the Mesh Storage Bag.Drain suction hose by turning cleaner ON and holding noz
151 2Attach hose to the unit. Follow steps "Using your Power Path™ Pro Tools" on page 13.3Dry hands and plug into an outlet, then turn ON.Ge
164Overlap strokes by 1/2 in. to prevent streaking. Make additional strokes without pressing the trigger to remove more solution.For heavily soiled ar
Welcome to Hoover ownership.Get cleaning confidence for up to 2 full years with the Hoover® limited warranty.
17Cleaning the dirty water tank:1 2Remove the Dirty Water Tank by pressing on latch and pulling the tank out at an angle.Pull up on back latch to open
183To clean Dirty Water Tank, place it under faucet and dispense high pressure clean water to backush any loose debris.4 5Be sure to clean the lte
19Cleaning the Nozzle:31 2Pull nozzle forward to remove.To prevent leaking, remove Solution Tank and Dirty Water Tank. With handle in upright position
205 6Position nozzle onto the base, making sure to align the tabs at the bottom of the nozzle with the notches on the base. Press down on nozzle latch
21Cleaning SpinScrub Brushes:Keeping your Power Path™ Pro running properly:1 2 3Flip cleaner on back. Grasp SpinScrub Brushes and pull out.Rinse off
22Removing the flat belt:CAUTIONTo reduce risk of injury from moving parts – Unplug before servicing.!!1 2 3Flip cleaner on its back to expose bottom o
235 6Pull up on hood and move to side. Hood will still be attached to unit. Make sure unit is in upright position. Slide off at belt and replace with
24If you need further assistance:If your product needs servicing within the warranty period, please contact Customer Service at 1-800-944-9200; Mon-Fr
25Troubleshooting:Any other servicing should be done by an authorized service representative.USE TROUBLESHOOTING GUIDE AS A FIRST STEP TO RESOLVE ANY
26ANY SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE Call 1-800-944-9200 USA & Canada In the event that further assistance is re
Safety InstructionsHow to assemble your Power Path™ ProGetting started with your Power Path™ ProUsing your Power Path™ ProHow to attach your Power Pat
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the
221ABCWARNING: This product contains chemicals known to the State of California to cause cancer, birth defects or reproductive harm. WASH HANDS AFTE
31 2 3Insert the handle into the base.Turn the dial clockwise to the “LOCK” position. Tip the Clean Water Tank in like this on the handle above the di
4Before you begin cleaning:Vacuum carpet and upholstery thoroughly with a Hoover® vacuum before use.Don’t use the carpet cleaner as a dry vacuum clean
51 42 3Press the Clean Water Solution Tank button on handle. Tilt the Clean Water Solution Tank out and remove.Fill Solution Tank with solution. Repla
65Tilt the Clean Water Solution Tank back onto the handle until it clicks.NOTE: Using more than the recommended amount of cleaning solution may cause
Komentáře k této Příručce